Видео

This looks like chrome??

I was waiting to see how it looks like behind welding helmet.

Why flameable gas is big no no? Some advice: "Propane is the most typical gas used for MIG Welding Guns. Propane is a widely used, readily available, and reasonably priced fuel that resembles gasoline. It has a low heat index, which results in a smooth, uniform weld and minimal heat distortion."

Also, most manufacturers imprint the alloy number on the rod. Another thing is, have only one rod alloy out at a time.

couple of questions : 1, when I have set it to 20cfh after press the button on the torch and then when it time out , it settles to about 30cfh . I have noticed that after I went to grind the tungsten put it back in the torch I saw that the flow reading had crept up to 35cfh and it was still climbing , slowly but still it was climbing. What does that mean ? Should it do that ? 2, I tried to weld as I am new to all this , as I welded it went to 20cfh , when stopped , settled to 30-ish cfh , then carried on like this for a few more goes . Then thought ok , stop for now , so I turned off the main valve , then just pressed the button to bleed off the gas . The flow gauge went down but the pressure gauge for the bottle stayed where it was . The main valve for the bottle was definitely 100% in the off position . After the flow gauge went right down , I turned the regulator adjusting screw all the way backed out so no pressure on the diaphragm but the the gauge for the bottle, what is left in the bottle stayed where it was . What does that mean ?

100% agree with the first 10-15 comments here , simple and to the point and clearly explained . Best video on youtube for setup the gas bottle Thank you very much

Can ypu weld with flux core?

A lot of structural steels are fairly low carbon but have about 1% or a bit more of Mn and and a small amount of Si as well. A rule of thumb for the hardenability of these steels is a carbon equiv content of C+(Mn+Si)/6. So for example a 0.2% carbon steel with 1.1% Mn and 0.4% Si would have a carbon equiv of about 0.45% and be somewhat hardenable. I think that this may be something like what you've got there.

Is the much difference in sparks between 304 vs 316?

Cual es la presión de trabajo del gas para soldar con la soldadora mig

Love this!! Thankyou for sharing your knowledge and experience!!

Watching from Philippine 🎉 student at Bangad National High School, Grade-11 SMAW track 😅

Possibly one of the worst videos on welding I have ever seen

That first mig weld was too cold. Turn up voltage a little bit more and it won’t spatter as much at all, sounds better, penetrate more, and won’t have lack of fusion on the first 1/4” of your weld.

My experience with gal pipe, stick welding, is you don't get a good weld most of the time, as it is not steel but malleable iron.

Come on man! You can make structural welds with flux-cored wire.👎👎

Thank you so much, will be referring this video to the students in our welding program🔥

This was so informative, you have no idea how much this video has helped me! Thank you so much!!

Thanks for the demo, however you should have used flux core versus Argon/CO2 unless I missed. something! I didn't hear you mention Flux core>?

Someone told me you cant weld galve pipe and keep the weld totally rustproof (apart from painitng which isn't 100% of course). Are there galve electrodes? Can I weld a galv pipe so it is an rust resistant as the pipe itself? Or do I just have to paint the wled to (help) stop rust? Thanks.

can someone explain the science please? what exactly happens without shielding in arc welding?

I knew this guy was a clown just the way he composed himself. He sure won one of my many awards.. B L O C K 👌

Mild steel, long cool sparks, carbon steel shorter hot sparks, stainless steel dim cool short sparks, white cast iron lots of reddish orange sparks like carbon steel, gray cast iron short orange sparks, titanium bright white sparks, magnesium occasional greenish white sparks, aluminum no sparks, nickel dim red orange sparks, tool steel bright yellow sparks with forking, carbide dim red sparks on sic wheel.❤

alright, now I just wonder how well it works with hardfacing wire. i just have mig without the gas... and was wondering about this for small jobs like fixing tools or hard facing hammers.

?

Ok, so what's your review on the cup? What size cup and cfm were you running?

Does this also works on stick mode?

What the size of circuit breaker can I use? Thank you.

This was insanely helpful!!! I've been reading my welding books over and over again to try to understand the concept of constant voltage and constant current power sources, and it never clicked till now. Thank you so much for going in depth in the video and also in the short bio of the video! Both of those combined improved my knowledge of CC and CV. Hopefully, I can pass my test now!!!

Excelente video Sergio Cruz, 1 Consulta esperando me puedas ayudar a disolver, ¿Cuáles son los calibres mínimos y máximos que podemos soldar con el Proceso MIG-MAG?. En el caso de estructuras metálicas, ce que utilizamos en SMAW el electrodo revestido normalmente E7018 igualmente con polaridad inversa, quisiera saber, si con MIG también ¿se podrán soldar estructuras pesadas en la industria de acero, aluminio, inoxidable? Saludos cordiales, en espera de tus comentarios quedo al pendiente. Muchas gracias

Pure poison fumes.

This is America, F... the metric system. Globalism sucks.

Does a 7018 rod contain any lead? Or only non-toxic metals?

Brilliantly explained!! Thanks!!

Nice job on what you’re doing! But there comes a time when you just gotta say damn! An throw that crap in the scrap metal pile! That’s one hell of a repair on a rim

Que pasa si la tierra lo pongo al positivo y la pistola al negativo a lo invertido ahi algún problema???

good teaches

That didn’t teach me shit, ima tig welder and that didn’t say shit to me other then what I already know and you didn’t say much about that stuff even… most of that stuff is common sense.

São 230 Psi. Não 2300.

Parabéns pela iniciativa

very good explaination, Thank you.

I am spark tester ms carbon high carbon spring

What does a tig weld on aluminum look like without a shielding gas?

Can welding be done using only argon gas?

technically penetrationis what you want for all metals or else the weld won't bond

And you rubbed them against what ? The cylinder?

You cannot MIG without gas, period. Metal Inert Gas is a process not a welder type. The type of welder is wire feed

These rods weld very nicely. The 6013s weld very well on vertical

No no no no… this guys is a hack!

May 2023: Just getting started as a hobbyist. Love to hear about the fundamentals. Thanks!